GBP (£)
DPA d:dicate™ 4011A Stereo Pair with Clips and Windscreens in Peli Case
The wide and versatile d:dicate™ Microphone series is legendary in the high-end recording and film production industry. Delivering clean, accurate sound, the mics in this series are used by professionals, who understand sound and insist on only using the best.
We have collected our award-winning d:dicate™ Recording Microphones in specialized stereo pairs that are matched within either ±0.5 dB, ±1 dB ±1.5 dB, depending on the pair you choose. Explore the stereo pairs below.
4011 Cardioid Stereo Pair
Even though the standard tolerances on our d:dicate™ microphones are extremely low, a stereo match is even closer. These specially selected d:dicate™ 4011A Cardioid Microphones are matched within ±1 dB on both frequency response and sensitivity. The pair comes in a heavy-duty Peli™ Case for safe transportation and easy access to the microphones and accessories.
This condenser microphone is renowned in recording studios and live applications around the world as an exceptional mic. State-of-the-art components have been carefully selected to provide optimal neutrality, accuracy and extremely low distortion.
- Modularity – interchangable capsules and preamplifiers
- Up to 120 dB dynamic range
- RF rejection between >60 and >40 dB
- Linear frequency response
- High SPL
- Superior gain before feedback
| Principle of operation | Pressure gradient | Total harmonic distortion (THD) | < 1% up to 139 dB SPL peak |
|---|---|---|---|
| Common mode rejection ratio (CMRR) | > 60 dB | Microphone length | 170 mm (6.7 in) |
| Directional pattern | Cardioid | S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL) | Typ. 76 dB(A) |
| Output balance principle | Impedance balancing with Active Drive | Capsule diameter | 19 mm (0.75 in) |
| Equivalent noise level, ITU-R BS.468-4 | Typ. 25 dB (correct with the attenuator in 0 dB or -20 dB setting) | Cable drive capability | 100 m (328 ft) |
| Microphone diameter | 19 mm (0.75 in) | Phase deviation for kit | < 10° |
| Equivalent noise level, A-weighted | Typ. 18 dB(A) re. 20 µPa (max. 20 dB(A)) | Minimum load impedance | 2 kΩ |
| Weight | 158 g (5.6 oz) | Matching tolerance (frequency response and sensitivity) | ±1 dB |
| Sensitivity, nominal, ±2 dB at 1 kHz | 10 mV/Pa; -40 dB re. 1 V/Pa | Output impedance | 200 Ω |
| Color | Matte black | Relative humidity (RH) | Up to 90% |
| Frequency range, ±2 dB, at 30 cm (11.8 in) | 40 Hz - 20 kHz | Switchable attenuator, filters etc. | 0 dB / -20 dB |
| Connector | XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase | Temperature range | -40°C to 45°C (-40°F to 113°F) |
| Frequency range | 20 Hz - 20 kHz | Max. SPL, peak before clipping | 159 dB |
| Current consumption | 2.8 mA | Polarity | +V at pin 2 for positive sound pressure |
| Cartridge type | Pre-polarized condenser | Dynamic range | Typ. 121 dB |
| Power supply (for full performance) | 48 V Phantom power (± 4 V) | Maximum output voltage, RMS | > 5 V |
